Scantronic 4603 Guide de l'utilisateur

Naviguer en ligne ou télécharger Guide de l'utilisateur pour Systèmes de contrôle d'accès de sécurité Scantronic 4603. Scantronic 4603 User guide [en] Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 12
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
496368 Issue 1 1 of 12
4600
Installation and User Guide
Compatible Equipment
4601 Long range and short range pendant transmitters
4602 Hand held PA
4603 Programmable transmitter
4604 Contact transmitter
4605 Short range dual channel transmitter
4608 PIR
4609 Smoke detector
7150 Viper radio vibration detector (supplied by Weyrad Elec-
tronics).
Vue de la page 0
1 2 3 4 5 6 ... 11 12

Résumé du contenu

Page 1 - Installation and User Guide

496368 Issue 1 1 of 124600Installation and User GuideCompatible Equipment4601 Long range and short range pendant transmitters4602 Hand held PA4603 Pro

Page 2 - Technical Specification

10 of 12 496368 Issue 1Figure 5. Fault Finding Displays ContinuedRemote setting transmitterjammed on. Check forobvious causes, e.g. testswitch turned

Page 3 - Programming

496368 Issue 1 11 of 12User CommandsFrom the KeypadFull Set User code + 2Unset User codePart Set User code + 1Omit Zones User code + 2 + OMIT + zone n

Page 4 - To Enter Programming Mode

12 of 12 496368 Issue 1

Page 5 - Defaults

2 of 12 496368 Issue 1IntroductionThe 4600 electronic intruder alarm system is a fully programmable, 8-zone,bells only, radio security system, designe

Page 6 - Engineering Program Commands

496368 Issue 1 3 of 12WiringFigure 1. External SAB Bell/Strobe and Internal Speaker ConnectionsNotes:1. SAB shown for negative applied. The connection

Page 7 - 496368 Issue 1 7 of 12

4 of 12 496368 Issue 1Figure 2. Setting the Site CodeConsult the sections for individual 4600 series transmitters for detailson setting the DIL switch

Page 8 - Walk Test

496368 Issue 1 5 of 12Programming CommandsTo change the factory default program use the commands listed in thissection as follows:1. Key in the comman

Page 9 - Fault Finding

6 of 12 496368 Issue 1Zone 1 Entry/Exit zone/part set/auto restore (PIR)Zone 2 Part set/entry route zone/auto restore (PIR, VIPER)Zone 3 Part set/entr

Page 10 - 10 of 12 496368 Issue 1

496368 Issue 1 7 of 12To change: Key in: Then: Notes DefaultZone Options 5n ENTER 1 = Double knock(n = zone number) 2 = Chime3 = Auto RestorePress Cle

Page 11 - User Commands

8 of 12 496368 Issue 1Leaving Programming ModeWhen all programming is complete:1. Remove the programming stencil and close the panel.2. Key in 99 then

Page 12 - 12 of 12 496368 Issue 1

496368 Issue 1 9 of 12Fault FindingUnder normal operating conditions, the Fault and Alarm LEDs are dark (thepower LED glows while mains is on). The Wa

Commentaires sur ces manuels

Pas de commentaire